Successful Fireplaces in Tight Houses

A central location, a tall chimney, and controlled combustion are the keys to a good burn. By John Gulland A version of this article first appeared in the May 1999 edition of the Journal of Light Construction Builders are beginning to hear more complaints that traditional masonry fireplaces leak smoke and burn too much wood for too little heat output. The fact is, open site-built masonry fireplaces have always been filthy, smoky, and inefficient, but these drawbacks were less noticeable in drafty, uninsulated houses. Today’s tighter homes, however, are less forgiving, and their occupants are less tolerant.

In addition, many modern fireplaces are used strictly as a design element, and many designers have no training in what makes one work. On top of that, many of the masons and other heating contractors who build fireplaces carry over outdated design traditions that are at the root of performance problems.

It doesn’t have to be that way. Building scientists now understand why traditional fireplace designs perform poorly, and masons, manufacturers, and hearth installers have responded with new products and techniques that eliminate past problems.

In this article, I’ll discuss the common causes of fireplace problems, and propose solutions for masonry fireplaces and heaters, as well as less expensive, efficient factory-built wood-burning fireplaces.

Why Fireplaces Fail When it comes to traditional open masonry fireplaces, masons have perpetuated outdated ideas about the smoke shelf, the mysteries of the smoke chamber, and the need for wide, but shallow-throat dampers. Today, it is clear that all three of these features work against successful fireplace performance (see Figure 1). The smoke shelf and shallow-throat damper both act as obstacles to straight exhaust flow. And the smoke chamber actually reduces the strength of a chimney’s draft by slowing and cooling the fireplace exhaust. The performance of many brick fireplaces can be improved immediately by removing the throat damper and smoke shelf, and installing a chain-operated damper at the top of the chimney. The results are a smooth, straight path for the exhaust and less smoking when a fire burns.

Figure 1. Traditional fireplaces leak smoke into living space and don’t produce heat efficiently. The curving smoke chamber, the throat damper and the smoke shelf all decrease the strength and stability of the chimney draft.

Just as hot exhaust in a chimney produces a pressure difference called a draft, so the relatively warm air in a house produces a pressure difference called "stack effect" when it is cold outside The buoyant warm air rises, producing a slight low pressure zone downstairs and higher pressure upstairs. Since most fireplaces are installed on lower floors, they experience negative pressure due to stack effect when it is cold outside. As soon as the air in the chimney falls below room temperature, the house becomes a better chimney than the chimney itself, and a cold backdraft gets started. The backdraft tends to stabilize because as the chimney becomes full of cold air, it cannot produce any draft to resist the suction of the house.

Stack Effect   A similar problem is caused by chimneys that fail to extend higher than all of the living space in a house. A short chimney cannot compete with a taller living space: the house makes more stack effect than the chimney makes in draft when no fire burns. (Figure 3). The higher pressure zone at the top of the house pushes air out through envelope leaks such as windows, attic access hatches and ceiling penetrations. The negative pressure low in the house draws cold outside air in through low level leaks, one of which is the fireplace. The house acts as a better chimney than the chimney itself. In these cases, the house is said to have a "taller effective stack" than the chimney. Air will tend to flow down through the chimney, then loop through the house to exit through the attic or upper-story wall leaks. To avoid these problems, chimney tops should always penetrate the highest section of the conditioned living space.

Figure 3. Chimneys built on outside walls are often too short to counter the house’s stack effect and are prone to backdrafts. Moving the chimney closer to the center of the house ensures a tall chimney with a strong draft.

In all cases, the cold hearth syndrome has two necessary ingredients without which it will not occur: a misplaced chimney (outside or too short) and a fireplace located low in the house. If we could move the fireplace and its chimney towards the center of a house, the syndrome would vanish.

Unfortunately, moving a problem fireplace is not usually practical after it’s been built, but you may still be able to minimize the cold hearth syndrome by keeping the chimney from falling below room temperature. One way to do this is to trick the fireplace into thinking it is inside. This requires building a sealed, insulated chase using the same materials and techniques as sealed house wall construction. The chase can then be vented to the inside so that warm house air circulating in it will keep it at about house temperature.

But a better solution is to design out cold hearth syndrome at the planning stage by bringing the fireplace and chimney in from the cold. Ideally the fireplace should be located centrally, in the heart of the home, so that the chimney will penetrate the roof closer to its highest point. This makes for a tall chimney that doesn't fall below room temperature, the two ingredients that form the basis of reliable and stable draft. Straight venting systems also work better, so elbows and offsets in the chimney should be avoided.

Makeup Air
While improper design and location is a major cause of poor fireplace performance, tighter house construction and powerful exhaust fans must share some of the blame. By installing vapor barriers and using doors and windows that have sealing gaskets, builders commonly reduce air leakage by more than 75% compared with the standard construction of 20 years ago. And homes are now commonly equipped with high-volume exhaust fans, such as those in downdraft kitchen ranges, which can move air out of the house at a rate of 600 cubic feet per minute (cfm) or more. Because tightly sealed house walls will not allow this much air back into the house through leakage, these powerful fans create negative pressure that can cause a chimney to backdraft and fill a house with smoke (Figure 4).

One standard fix for smoky fireplaces has been to install a supply of outdoor air in the belief that air starvation is the root cause. While lack of combustion air may be a problem in some cases, supplying outdoor air to the fireplace through a duct is certainly not the cure. Two research studies, one conducted in Canada on a series of factory-built fireplaces and one done in the U.S. on a masonry fireplace, looked into the behavior of outdoor combustion air supplies. In both studies, the fireplaces were installed within chambers that could be depressurized continuously after a fire was lit. As the fires died down to charcoal, technicians monitored carbon monoxide readings in the chamber to see when exhaust began to spill from the fireplaces. Tests were done with and without combustion air supplied from outside the depressurized chamber. No consistent difference in spillage timing or amount could be found whether or not outdoor air was supplied.

Figure 4. In tight houses, depressurization from cooktop vents, dryer vents, and other exhaust fans can cause fireplaces to backdraft and spill smoke into the room. Instead of ducting combustion air to the fireplace, which does nothing to change room pressure, add a makeup air system linked to the exhaust fans.

The reason is simple: Air flows to zones of lower pressure. If a room is depressurized to the point where its low pressure overwhelms the chimney draft, smoke will flow into the room. Obviously, ducting makeup air to the fireplace doesn’t work. In fact, building code authorities are currently removing mandatory outdoor air requirements for fireplaces that were added only a few years ago, just before research debunked the idea.

Where a notorious air-guzzling downdraft kitchen range causes excessive depressurization, many homeowners will simply not use their range exhaust when the fireplace is burning. But another solution is to install a makeup air system that is interlocked to the range exhaust switch. This kind of makeup air system would force air into the house to compensate for the kitchen range exhaust flow. This would prevent depressurization, and solve the smoky fireplace problem.

Controlled Combustion
The design of the fireplace itself plays a big role in the level of satisfaction it provides. The internal features that produce efficient, smokeless combustion tend to be the same as those that produce reliable chimney venting and trouble-free operation. To help guide fireplace design, here is a simple rule of thumb that neatly summarizes a lot of expensive research: The more air a fireplace demands for normal operation, the more fussy and spillage-susceptible it will be.

Open fireplaces are the worst because they consume huge amounts of air — much more than is needed for combustion — which cools the system, thereby reducing draft. If you insist on a traditional fireplace, make sure to equip it with doors. Blocking most of the dilution air to the firebox causes the average exhaust temperature to go way up. Higher average temperature means stronger, more stable draft.

If you don't want glass doors or much heat, consider a gas hearth. Do the same if the architect’s plans call for a hearth in an outside chase situated at the low eaves of a cathedral roof. If you can't relocate the fireplace more centrally, you will probably be happier with a direct-vent gas fireplace.

Trained Installers In the last 20 years, building science research has clearly shown how fireplaces behave in houses. These insights are now being promoted through professional training programs. When planning for a traditional masonry or factory-built fireplace, or even a wood stove, use suppliers, installers, or masons who understand the pitfalls of outdated ideas and impractical designs. Use fireplace suppliers and installers who are graduates of one of these training programs. Hearth Education Foundation in the U.S. Wood Energy Technical Training (WETT) in Canada Masonry Heater Association

Figure 7. Factory-built fireplaces don’t have to look metallic. The masonry surround for this metal fireplace gives a traditional look along with predictable performance, at a savings over a site-built masonry fireplace.